Once the code is entered, you will be able to reset the system and make changes to any settings. This can be done by pressing the “Program” button twice followed by entering your four-digit access code. In order to reset your Honeywell Alarm System, you will need to re-program the system. Wait until you hear repeated keypad beeps before pressing any buttons so that all components in your system recognize that power is back on. Once it is unplugged, insert one end into its corresponding wall socket and plug in the other end into where you had previously located it in order for power to reach your Honeywell Alarm System again. Make sure all connections have been properly disconnected before you proceed. To reconnect the power and reset your Honeywell alarm system, start by unplugging it from its wall socket. Depending on the model of your system, there will either be a plug with two or three pins. To do this, locate the plug next to your Honeywell alarm system. When the power is disconnected from the system (or has been disconnected for an extended period of time), you will need to reconnect the power to reset the Honeywell Alarm System. Be sure to refer to your alarm’s user manual before attempting a system reset procedure – some models may require additional steps or warnings prior to initiating a complete system reset. ![]() This indicates that your system has been reset successfully and is ready to program again with your new preferences. Once located, press and hold the reset switch for 10 seconds until you hear a short beep sound. On other systems like Vista Series or LYNX Touch it’s often on the circuit board inside the control panel enclosure. For the Lyric and Wi-Fi Security Systems, the reset switch is typically located near the backup battery. Depending on your system type, this can be found in different locations. In some cases, when you want to reset your Honeywell Alarm System, all you need to do is locate the reset switch. The alarm should now be reset and any codes and/or settings which were previously programmed will no longer be available Once all switches are unset, put the back cover on firmly and press the * (star) key followed by 8-0-0 on your key pad. Make sure to note which switches are set in what position before adjusting them – it’s helpful to make a pencil mark if you won’t be able to remember their original location. On some systems, this may require an additional adjustment with a small screwdriver or other tool. Once removed, locate the system’s programming switches. ![]() This will require a Phillips screwdriver to remove the security screws. Remove the back cover of the control panelīefore beginning the reset procedure, locate and remove the back cover of your control panel. Let’s go over all the different methods available to you. ![]() There are a few different ways to reset your Honeywell alarm system, and each method has its own specific instructions. It is also a great troubleshooting step if something isn’t working properly with your system. Resetting your Honeywell alarm system is a necessary step to take if you want to make changes to your system such as adding or deleting users. Once all components have been disconnected, you can proceed with resetting your system. This includes wires, plugs, and other connections that may be attached to each other. After doing this, make sure all components of your alarm system are disconnected from each other. ![]() You can disconnect the power supply by unplugging the transformer from any power source. It may be necessary to disconnect power to the security system in order to complete a code reset.īefore resetting your Honeywell Alarm System, it is important to disconnect the power supply to ensure that no electric shocks or circuits are broken during the process. If you are unable to enter a passcode, consult with your local dealer or Honeywell representative to provide assistance in resetting the code. When successful, the armed/disarmed indicator light will turn off, indicating that the system has been disarmed. This can be done by entering your passcode on the keypad and pressing the ‘Disarm’ button. Let’s take a closer look at each step in the preparation process.īefore performing a full reset on your Honeywell alarm system, it is imperative that you disarm the system first. This includes making sure your power is disconnected, identifying the make and model of your alarm system, and having your manual handy. It is important that you prepare your alarm system beforehand to ensure everything goes smoothly during the reset. Resetting your Honeywell alarm system can be a daunting task, but if you take the right steps, the whole process can be relatively simple. 2.2 Locate the reset switch and press it.2.1 Remove the back cover of the control panel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |